|
6mmHOT.com |
|
|
|
Home Page The 6.5 x 47 Lapua cartridge with the 6mm version (6 x 47 Lapua) and other cartridges |
The 6x47 Lapua vs the 6mm XC|
The 6 x 47 Lapua cartridge is a rather new
6mm cartridge designed off a necked down 6.5 x47 Lapua cartridge. Lapua
brass is readily available in the U.S. and may be
purchased through many commercial suppliers. While many feel a 6.5mm
cartridge has merit, many also see this cartridge, in a 6mm version, as
fulfilling a long desired need for a cartridge that has the capability for magazine feeding from a short action rifle and inherently more
"horsepower" and a larger case capacity than the 6mm BR. The case is very close in size, and performance to a 6XC.
The quality of the Lapua brass is unbelievable, and it has a small
primer pocket and a small flash hole, which makes it even better.
From a lot of perspectives, this brass is an ideal high pressure vessel
that helps to make this 6mm cartridge a fast hot cartridge. Initial load testing shows that the 6 x 47 Lapua cartridge performs exceptionally well with 6mm 105-107 gr bullets, and the 115 gr DTAC bullets may be used as well. Initial results also indicate that H4350 and N160 are excellent powders for the cartridge with heavier bullets. |
NOTE: While this website was originally set up for the 6.5 x 47 Lapua and the 6 x 47 Lapua - we are now expanding it to include other cartridges. Please bear with us while it is under construction.
For the 6mm Dasher Page - Click Here
The 6.5 x 47 Lapua and the 6mm Version (6 x 47 Lapua)
Lapua Brass - The Ideal Pressure Vessel
The 6 x 47 Lapua essentially uses Lapua 6.5 x 47 cases necked down to 6mm. This brass is exceptional - very hard in the web area yet well annealed at the neck. The Lapua brass is very uniform, and it has a small primer pocket and a small flash hole. This combination of attributes makes this brass the ideal high pressure vessel for high velocity loadings. People who shoot Lapua's 6mmBR brass know how brass of this quility and these attributes can enhance the power and performance of a cartridge. This brass is being offered and sold by Graf & Sons (800) 531-2666 and other commercial vendors.
Reamers - Pacific Tool and Dave Kiff
Reamers for these cartridges are readily available from a variety of sources. The reamers for the 6 x 47 Lapua and the 6.5 x 47 Lapua were set up for highpower shooting as "no neck turn" reamers with approximately .005" neck clearance. The body dimensions of these 6mm reamers are also tighter than the standard CIP print for the 6.5 x 47 Lapua Cartridge. These reamers are currently available through David Kiff at Pacific Tool (541) 826-5808.
If you expect to neck turn and wish to set up a reamer to shoot neck turned brass, or just want a tighter neck, call Dave Kiff at Pacific Tool and he will set up a reamer to your requirements.
To see the 6 x 47 Lapua Match Reamer for 6mm 85-107 gr bullets - CLICK HERE!
To see the 6.5 x 47 Lapua Match Reamer for 6.5mm 120-142 gr. bullets - CLICK HERE!
Load & Chrono Info for both the 6mm and 6.5mm versions - CLICK HERE!
6XC Conversion
Another option to set up a 6 x 47 Lapua is to use a 6XC reamer and hold it short approximately .050" (actually .0486"). You can use a 6XC sizing die (with .050" ground off the bottom and with the decapping pin changed to a small decapping pin). The only thing you are required to do is neck down the 6.5 x47 Lapua cases by running them through the modified 6XC resizing die, then load them and shoot them. On initial set up there is no neck turning, no trimming, and no special fire forming!
For info on the NewAR-15 6mm Cartridge **Click Here**
For the 6mm Dasher Page - Click Here
The 6.5 x 47 Lapua and the 6mm Version (6 x 47 Lapua)
Lapua Brass - The Ideal Pressure Vessel
The 6 x 47 Lapua essentially uses Lapua 6.5 x 47 cases necked down to 6mm. This brass is exceptional - very hard in the web area yet well annealed at the neck. The Lapua brass is very uniform, and it has a small primer pocket and a small flash hole. This combination of attributes makes this brass the ideal high pressure vessel for high velocity loadings. People who shoot Lapua's 6mmBR brass know how brass of this quility and these attributes can enhance the power and performance of a cartridge. This brass is being offered and sold by Graf & Sons (800) 531-2666 and other commercial vendors.
Reamers - Pacific Tool and Dave Kiff
Reamers for these cartridges are readily available from a variety of sources. The reamers for the 6 x 47 Lapua and the 6.5 x 47 Lapua were set up for highpower shooting as "no neck turn" reamers with approximately .005" neck clearance. The body dimensions of these 6mm reamers are also tighter than the standard CIP print for the 6.5 x 47 Lapua Cartridge. These reamers are currently available through David Kiff at Pacific Tool (541) 826-5808.
If you expect to neck turn and wish to set up a reamer to shoot neck turned brass, or just want a tighter neck, call Dave Kiff at Pacific Tool and he will set up a reamer to your requirements.
To see the 6 x 47 Lapua Match Reamer for 6mm 85-107 gr bullets - CLICK HERE!
To see the 6.5 x 47 Lapua Match Reamer for 6.5mm 120-142 gr. bullets - CLICK HERE!
Load & Chrono Info for both the 6mm and 6.5mm versions - CLICK HERE!
6XC Conversion
Another option to set up a 6 x 47 Lapua is to use a 6XC reamer and hold it short approximately .050" (actually .0486"). You can use a 6XC sizing die (with .050" ground off the bottom and with the decapping pin changed to a small decapping pin). The only thing you are required to do is neck down the 6.5 x47 Lapua cases by running them through the modified 6XC resizing die, then load them and shoot them. On initial set up there is no neck turning, no trimming, and no special fire forming!
For info on the NewAR-15 6mm Cartridge **Click Here**
Copyright . Robert Whitley. All rights reserved.
